Project

What to do if the build plate does not adhere

3D Printing, Blog /

I am printing with a Creality Ender 3 V3 KE. I encountered an issue where the model would not adhere to the build plate. The filament is PLA. I dealt with the issue in the following order: 1. Make the X-axis parallel to the Z-axis 2. Adjust the Z-axis. It is within approximately 0.20 mm. 3. Adjust the filament and build plate. I set the build plate temperature to 210 degrees and 70 degrees, respectively, which are higher. 4. Set the brim. 5. Slow down the Initial Printing Speed. I set it to 1/4 of the initial value. 6. Increase the height and width of the Initial Layer. With these […]

What to do if the build plate does not adhere Read More »

97 900SS generator upgraded to three phase

900SS, Project /

I want to upgrade the single-phase generator of my 97 900SS to a three-phase one. The 98 900SS Final Edition comes with a DENSO three-phase generator. Looking at the parts list, the 97 SS and 98SS FE have the same parts except for the generator… After some research, it appears that the parts list is incorrect. Parts Needed The parts you need are as follows 26420471A Generator DENSO 24220262AB Generator Cover Bolts and nuts to secure the generator Spacer to replace the generator core Other small parts Single Phase Generator ~97 Three-phase generator 98~ Generator Cover ~97 Generator cover 98~ Crankshaft ~97 Crankshaft 98~ Flywheel ~97 Flywheel 98~ Concerns Different

97 900SS generator upgraded to three phase Read More »

I tried making tofu yo, part 1

Blog, Foods, Project /

I tried making tofu yo. I didn’t have any awamori, so I used vodka. It’s the same, right? Strong canned awamori, which is popular among foreigners, is apparently made with vodka, so I made it believing it was the same. Ingredients 500g firm tofu 350g rice koji 40g salt Appropriate amount of awamori (over 40% alcohol) 2/3 teaspoon red koji A little sugar Process Cut the tofu into 2-3cm cubes Drain the water. Drain with kitchen paper Sprinkle with salt and let dry until the surface is hard Mix rice koji, red koji, salt, and sugar to make the dipping sauce Put the tofu in a Tupperware and sprinkle with

I tried making tofu yo, part 1 Read More »

I made pancetta part 3

Blog, Foods, Pancetta, Project /

It’s been a week since I prepared the pancetta. It seems to be drying nicely. It doesn’t have any unpleasant smell. Rinse with water. I sliced ​​it thinly and tasted it, and it was a little salty, so I soaked it for about 10 minutes to remove the salt. Wipe off the moisture, wrap it in cooking paper, and start the drying process. It will be ready to eat in about a week.

I made pancetta part 3 Read More »

I tried making a wet blaster Part 2

Blog, Project, Wet Blaster /

I found a great guy on YouTube. Matthew from MatthewMCRepairInspired by another YouTuber who made a huge wooden aquarium, he made a huge blast cabinet measuring 106x76cm using plywood and 2×4 lumber. It’s made of wood, but it’s completely waterproof and can be used as a blast cabinet with no problems. Compared to iron cabinets, which require sheet metal welding, the hurdle is low. To be honest, I can make it with just the tools I have on hand. However, if I were to make it as is, the size would be a little large. Maybe I should shrink it to the commonly used cabinet size of 93×58? Astro Product’s

I tried making a wet blaster Part 2 Read More »

I made a 97 900SS battery box

900SS, Blog, Project /

I had a separate FCR 39 installed on my 97 900SS, but I couldn’t decide on the placement of the wiring, battery box, coil, and igniter. I had to go through a lot of trial and error. This time, I changed the position of the battery and rerouted the wiring, and I think it fit in pretty well. I ended up placing the regulator, coil and igniter just behind the stem, with the FCR behind that and the battery just in front of the vertical cylinder. The current FCR uses a funnel, but with this arrangement, the air cleaner should fit in without any problems. The FCR settings are Needle

I made a 97 900SS battery box Read More »